Difference between revisions of "User:Debra Tabron/sandbox"

From Enviro Wiki
Jump to: navigation, search
Line 29: Line 29:
  
 
==LNAPL Mobility Conceptualized==
 
==LNAPL Mobility Conceptualized==
[[File:Kirkman1w2Fig1.png|thumb|Figure 1.  LNAPL Distribution in a research sand tank<ref>Hawkins, A. M., 2013.  Processes Controlling the behavior of LNAPLs at groundwater surface water interfaces, Master of Science Thesis, Colorado State University, Ft. Collins, Colorado.  [[media:Hawkins2013_LNAPL_at_GW_SW_Interfaces.pdf | Report.pdf]]</ref>.]]
+
[[File:Kirkman1w2Fig1.png|thumb|left|Figure 1.  LNAPL Distribution in a research sand tank<ref>Hawkins, A. M., 2013.  Processes Controlling the behavior of LNAPLs at groundwater surface water interfaces, Master of Science Thesis, Colorado State University, Ft. Collins, Colorado.  [[media:Hawkins2013_LNAPL_at_GW_SW_Interfaces.pdf | Report.pdf]]</ref>.]]
 
Figure 1 shows a research tank with a well screen in a porous media (sand) containing LNAPL.  The LNAPL fluoresces under ultraviolet (UV) light, while water and air do not.  The column of yellow fluorescence in the well represents the gauged LNAPL thickness and corresponds to the vertical interval over which LNAPL flows in the formation<ref name= "Huntley2000">Huntley, D., 2000. Analytic determination of hydrocarbon transmissivity from baildown tests. Groundwater, 38(1), pp.46-52. [https://doi.org/10.1111/j.1745-6584.2000.tb00201.x doi: 10.1111/j.1745-6584.2000.tb00201.x]</ref>.  The yellow fluorescence to the left of the well represents LNAPL occurring within soil pores.  Below the potentiometric surface line, the pores are dominated by water (dark pores) and LNAPL.  Above this line LNAPL and water still exist in pores, but the air saturation increases with elevation.  The incomplete yellow fluorescence in the formation illustrates how water and LNAPL occupy pores over the mobile interval.  This occurs because the mobile LNAPL cannot displace all of the water from the pores.
 
Figure 1 shows a research tank with a well screen in a porous media (sand) containing LNAPL.  The LNAPL fluoresces under ultraviolet (UV) light, while water and air do not.  The column of yellow fluorescence in the well represents the gauged LNAPL thickness and corresponds to the vertical interval over which LNAPL flows in the formation<ref name= "Huntley2000">Huntley, D., 2000. Analytic determination of hydrocarbon transmissivity from baildown tests. Groundwater, 38(1), pp.46-52. [https://doi.org/10.1111/j.1745-6584.2000.tb00201.x doi: 10.1111/j.1745-6584.2000.tb00201.x]</ref>.  The yellow fluorescence to the left of the well represents LNAPL occurring within soil pores.  Below the potentiometric surface line, the pores are dominated by water (dark pores) and LNAPL.  Above this line LNAPL and water still exist in pores, but the air saturation increases with elevation.  The incomplete yellow fluorescence in the formation illustrates how water and LNAPL occupy pores over the mobile interval.  This occurs because the mobile LNAPL cannot displace all of the water from the pores.
  
 
LNAPL mobility can be described mathematically by Darcy’s Law, an empirically derived equation describing the flow of fluids through porous media where the specific discharge, ''q'', is equal to the product of the hydraulic conductivity, ''K'', and the hydraulic gradient, ''i''.  While this is the same Darcy’s Law that is used to describe groundwater flow (see [[Advection and Groundwater Flow]]), there is an important additional term, Relative Permeability, that is included when using Darcy’s Law to describe the flow of LNAPL in the subsurface.  Relative permeability is the ratio of the effective permeability of a fluid at a specified saturation to the intrinsic permeability of the medium at 100-percent saturation<ref>Mercer, J.W. and Cohen, R.M., 1990. A review of immiscible fluids in the subsurface: properties, models, characterization and remediation. Journal of contaminant hydrology, 6(2), pp.107-163. [Mercer, J.W. and Cohen, R.M., 1990. A review of immiscible fluids in the subsurface: properties, models, characterization and remediation. Journal of contaminant hydrology, 6(2), pp.107-163. [https://doi.org/10.1016/0169-7722(90)90043-G doi: 10.1016/0169-7722(90)90043-G]</ref>.  The USEPA (1996)<ref name= "USEPA1996">USEPA, 1996.  How to effectively recover free product at leaking underground storage sites.  A guide for state regulators.  USEPA 510-R-96-001.  U.S. Environmental Protection Agency, 162 pp. [[media:USEPA1996_510_R-96_001_Recover_Free_Prod_at_LUSTS.pdf| Report.pdf]]</ref> describes relative permeability this way:
 
LNAPL mobility can be described mathematically by Darcy’s Law, an empirically derived equation describing the flow of fluids through porous media where the specific discharge, ''q'', is equal to the product of the hydraulic conductivity, ''K'', and the hydraulic gradient, ''i''.  While this is the same Darcy’s Law that is used to describe groundwater flow (see [[Advection and Groundwater Flow]]), there is an important additional term, Relative Permeability, that is included when using Darcy’s Law to describe the flow of LNAPL in the subsurface.  Relative permeability is the ratio of the effective permeability of a fluid at a specified saturation to the intrinsic permeability of the medium at 100-percent saturation<ref>Mercer, J.W. and Cohen, R.M., 1990. A review of immiscible fluids in the subsurface: properties, models, characterization and remediation. Journal of contaminant hydrology, 6(2), pp.107-163. [Mercer, J.W. and Cohen, R.M., 1990. A review of immiscible fluids in the subsurface: properties, models, characterization and remediation. Journal of contaminant hydrology, 6(2), pp.107-163. [https://doi.org/10.1016/0169-7722(90)90043-G doi: 10.1016/0169-7722(90)90043-G]</ref>.  The USEPA (1996)<ref name= "USEPA1996">USEPA, 1996.  How to effectively recover free product at leaking underground storage sites.  A guide for state regulators.  USEPA 510-R-96-001.  U.S. Environmental Protection Agency, 162 pp. [[media:USEPA1996_510_R-96_001_Recover_Free_Prod_at_LUSTS.pdf| Report.pdf]]</ref> describes relative permeability this way:
  
 +
blockquote>The relative permeability of a particular geologic media that is completely saturated with a particular fluid is equal to the intrinsic permeability. When more than one fluid (i.e., air, water, petroleum hydrocarbon) exists in a porous medium, the fluids compete for pore space thereby reducing the relative permeability of the media and the mobility of the fluid. This reduction can be quantified by multiplying the intrinsic permeability of the geologic media by the relative permeability. As with saturation, the mobility of each fluid phase present varies from zero (0% saturation) to one (100% saturation).</blockquote>
 +
 +
[[File:Kirkman1w2Fig2.png|thumb|Figure 2.  Hypothetical relative permeability curves for water and an LNAPL in a porous medium<ref name= "USEPA1996"/><ref>Newell, C. J., S. D. Acree*, Ross, R.R., and Huling, S.G. 1995. Light non-aqueous phase liquid. U.S. Environmental Protection Agency, Washington, DC. EPA/540/S-95/500 (NTIS 95-267738) [[media:Newell1995_EPA_540_S-95_500_lnapl.pdf | Report.pdf]]</ref><ref>Williams, D.E. and Wilder, D.G., 1971. Gasoline Pollution of a Ground‐Water Reservoir—A Case History a. Groundwater, 9(6), pp.50-56. [https://doi.org/10.1111/j.1745-6584.1971.tb03577.x doi: 10.1111/j.1745-6584.1971.tb03577.x]</ref>.]]
 +
Figure 2 shows an example of relative permeability curves for a water-LNAPL system. The curves representing water saturation (starting at top right, blue line) and hydrocarbon saturation (starting at top left, red line) are contrary to one another and divide the figure into three flow zones. Zone I, where hydrocarbon saturation is relatively high, is dominated by hydrocarbon flow.  Water saturation is relatively high in Zone III, and therefore water flow is dominant. Flow of both water and LNAPL characterizes Zone II.
 +
 +
The relative permeability term scales the LNAPL conductivity to the fraction of pores occupied by LNAPL.  If LNAPL occupies 50 percent of the pores, then it will only flow through LNAPL-filled pores and therefore does not use the entire permeability of the soil.  If the sum of the pores is considered a pipe, then a pipe half full will transmit less LNAPL than a pipe completely full for a given pressure gradient. The relative permeability term is used to account for this effect.
 +
 +
LNAPL saturation varies with elevation across the gauged LNAPL thickness, where LNAPL conductivity is lowest near the oil/water interface and highest near the air/LNAPL interface.  To provide a single metric for LNAPL mobility, the conductivity must be summed across the mobile LNAPL interval to give the LNAPL transmissivity.
 +
 +
[[File:Kirkman1w2Fig3.png|thumb|left|Figure 3.  Aquifer transmissivity versus hydraulic conductivity.]]
 +
LNAPL transmissivity has been identified as a key metric for evaluating the likely effectiveness of direct LNAPL recovery compared to traditional measurements such as gauged LNAPL thickness in monitoring wells<ref>Kolhatkar, R., Kremesec, V., Rubin, S., Yukawa, C. and Senn, R., 1999. Application of field and analytical techniques to evaluate recoverability of subsurface free phase hydrocarbons. Petroleum Hydrocarbons and Organic Chemicals in Ground Water, pp.5-15.</ref><ref>Lundy, D.A. and Zimmerman, L.M., 1996, May. Assessing the recoverability of LNAPL plumes for recovery system conceptual design. In Proceedings of the 10th National Outdoor Action Conference and Expo (pp. 13-15).</ref><ref name= "Huntley2000"/><ref name= "Kirman2013">Kirkman, A.J., 2013. Refinement of Bouwer‐Rice baildown test analysis. Groundwater Monitoring & Remediation, 33(1), pp.105-110. [https://doi.org/10.1111/j.1745-6592.2012.01411.x  doi: 10.1111/j.1745-6592.2012.01411.x]</ref><ref name= "ASTM2013">ASTM, 2013.  ASTM E2856-13, Standard guide for estimation of LNAPL transmissivity, ASTM International, West Conshohocken, PA.]</ref><ref name= "Charbeneau2016">Charbeneau, R., A. Kirkman, and R. Muthu, 2016.  API LNAPL Transmissivity Workbook: A Tool for Baildown Test Analysis – User Guide.  American Petroleum Institute Publication 4762.</ref><ref name= "Palmier2016">Palmier, C., Dodt, M. and Atteia, O., 2016. Comparison of Oil Transmissivity Methods Using Bail‐Down Test Data. Groundwater Monitoring & Remediation, 36(3), pp.73-83.[[media:Palmier2016_LNAPLBaildownTesting.pdf| Report.pdf]]</ref><ref>Lenhard, R.J., Rayner, J.L. and Davis, G.B., 2017. A practical tool for estimating subsurface LNAPL distributions and transmissivity using current and historical fluid levels in groundwater wells: Effects of entrapped and residual LNAPL. Journal of contaminant hydrology, 205, pp.1-11. [[media:Lenhard2017_Estimating_Subsurface_LNAPL.pdf | Report.pdf]]</ref>).  LNAPL transmissivity represents the volume of LNAPL flow a formation can produce per unit time over a unit width for a unit hydraulic gradient.  Aquifer transmissivity is the primary metric for evaluating how much water can be produced from a water bearing unit in the subsurface and accounts for the thickness of the saturated aquifer and the ease with which the aquifer can transmit a given fluid per unit volume. The concept of transmissivity is illustrated in Figure 3.  It is reasonable to apply similar thinking to estimation of the amount of LNAPL that could be produced by a particular subsurface matrix, and therefore transmissivity has become a key metric used to predict whether direct recovery (direct pumping) of LNAPL is likely to be effective.
 +
 +
The average LNAPL recovery rate was shown to be closely related to the average LNAPL transmissivity as well as to the LNAPL thickness in a series of 10-hour pump tests of three wells at an LNAPL-impacted site (Table 1, ITRC 2018)<ref name= "ITRC2018"/>.  The measured LNAPL thickness in the source well (MW-1) was 3.7 times higher than in the LNAPL fringe well (MW-3), while the ratio of their average LNAPL transmissivities was 5. The average recovery rate was 12 times greater at the source well than at the fringe well.  In this study, LNAPL thickness, average transmissivity and average recovery rate were all strongly correlated, with correlation coefficients of 0.94 and above.
  
  

Revision as of 21:26, 4 February 2020

Many contaminated sites use active remedies such as pump-and-treat or in situ remediation to clean up impacted groundwater. Natural attenuation processes such as natural degradation or hydrodynamic dispersion also contribute to the cleanup. As remediation progresses, a point is often reached when the time required to reach the remedial objectives using the active remedy is roughly the same as the time required if the active remedy is shut down, and the continuing remediation of the site is provided by natural attenuation processes alone. From that point forward, the extra effort and expense of the active remedy provides no benefit over natural attenuation, and it may be appropriate to transition the site to Monitored Natural Attenuation (MNA). This article deals with currently available tools and approaches that can be used to support a decision to transition from active remediation to MNA.

Related Article(s):

  • LNAPL Source Zone Conceptual Models (Coming soon)
  • LNAPL Remediation Technologies (Coming soon)


CONTRIBUTOR(S): Andrew Kirkman


Key Resource(s):

Introduction

LNAPL can be found in the subsurface in three different states:

  1. Residual LNAPL is trapped and immobile but can undergo composition change and generate dissolved hydrocarbon plumes and/or vapor sources in the unsaturated zones.
  2. Mobile LNAPL is LNAPL at greater than the residual saturation which can therefore accumulate in a well where it is potentially recoverable. However, in this state LNAPL saturation is insufficient to drive migration (i.e., the LNAPL body is not expanding).
  3. Migrating LNAPL is LNAPL at greater than the residual saturation that expands into previously unimpacted locations over time (e.g., LNAPL appears in a monitoring well that had no previous detections).

When released to the subsurface, light non-aqueous phase liquids form source zones which evolve over time with changing impacts to soil, groundwater, and at some sites surface water. Shallow unsaturated soils may also be impacted by intrusion of vapors released by the LNAPL. (See Vapor Intrusion - Separation Distances from Petroleum Sources.) LNAPL mobility is typically highest during the time of the release to the environment. Once the release stops, LNAPL mobility and the potential for migration rapidly decrease. The LNAPL body may initially contain mobile LNAPL near the release point. However, as the LNAPL body spreads, the driving head and pressure gradient decrease, and the LNAPL thickness (a key factor in mobility) decreases. The LNAPL body also begins to weather, losing volatiles and biodegradable compounds. Over time, this weathering process alters the LNAPL composition and stabilizes the LNAPL body, and the fraction of LNAPL that remains mobile therefore decreases[1][3][4]. LNAPL bodies from historical releases are dominated by immobile residual LNAPL.

Because LNAPL bodies evolve over time, LNAPL mobility is a much more significant concern during and immediately after the release period than it is after the release is halted. Tools are now available to assess the magnitude of LNAPL mobility at individual release sites to support decision making regarding potential remedial actions. One such tool is the American Petroleum Institute’s LNAPL Distribution and Recovery Model (LDRM) which is available as a free download. Please see the LNAPL Mobility and Recovery section below for a more complete discussion of modeling tools.

In order to understand LNAPL mobility, key concepts from the science of multiphase flow in porous media (e.g. soil and aquifer material) are important. Consider dry soil to which a small amount of water is added. The open pore space in the soil, initially filled with 100 percent air, now contains a mix of air and water. Therefore, a soil can have more than one fluid within the pores (“multiphase”). The fraction of pore space filled with a given fluid is termed “saturation”. The air saturation of the initially dry soil was 100% and the water saturation was zero. When considering a petroleum release site, three different fluids may exist in the pore space: air, water and LNAPL. The sum of the saturation of the three fluids is 100%. All three fluids can exist within the subsurface with varying saturations.

LNAPL Mobility Conceptualized

Figure 1. LNAPL Distribution in a research sand tank[5].

Figure 1 shows a research tank with a well screen in a porous media (sand) containing LNAPL. The LNAPL fluoresces under ultraviolet (UV) light, while water and air do not. The column of yellow fluorescence in the well represents the gauged LNAPL thickness and corresponds to the vertical interval over which LNAPL flows in the formation[6]. The yellow fluorescence to the left of the well represents LNAPL occurring within soil pores. Below the potentiometric surface line, the pores are dominated by water (dark pores) and LNAPL. Above this line LNAPL and water still exist in pores, but the air saturation increases with elevation. The incomplete yellow fluorescence in the formation illustrates how water and LNAPL occupy pores over the mobile interval. This occurs because the mobile LNAPL cannot displace all of the water from the pores.

LNAPL mobility can be described mathematically by Darcy’s Law, an empirically derived equation describing the flow of fluids through porous media where the specific discharge, q, is equal to the product of the hydraulic conductivity, K, and the hydraulic gradient, i. While this is the same Darcy’s Law that is used to describe groundwater flow (see Advection and Groundwater Flow), there is an important additional term, Relative Permeability, that is included when using Darcy’s Law to describe the flow of LNAPL in the subsurface. Relative permeability is the ratio of the effective permeability of a fluid at a specified saturation to the intrinsic permeability of the medium at 100-percent saturation[7]. The USEPA (1996)[8] describes relative permeability this way:

blockquote>The relative permeability of a particular geologic media that is completely saturated with a particular fluid is equal to the intrinsic permeability. When more than one fluid (i.e., air, water, petroleum hydrocarbon) exists in a porous medium, the fluids compete for pore space thereby reducing the relative permeability of the media and the mobility of the fluid. This reduction can be quantified by multiplying the intrinsic permeability of the geologic media by the relative permeability. As with saturation, the mobility of each fluid phase present varies from zero (0% saturation) to one (100% saturation).

Figure 2. Hypothetical relative permeability curves for water and an LNAPL in a porous medium[8][9][10].

Figure 2 shows an example of relative permeability curves for a water-LNAPL system. The curves representing water saturation (starting at top right, blue line) and hydrocarbon saturation (starting at top left, red line) are contrary to one another and divide the figure into three flow zones. Zone I, where hydrocarbon saturation is relatively high, is dominated by hydrocarbon flow. Water saturation is relatively high in Zone III, and therefore water flow is dominant. Flow of both water and LNAPL characterizes Zone II.

The relative permeability term scales the LNAPL conductivity to the fraction of pores occupied by LNAPL. If LNAPL occupies 50 percent of the pores, then it will only flow through LNAPL-filled pores and therefore does not use the entire permeability of the soil. If the sum of the pores is considered a pipe, then a pipe half full will transmit less LNAPL than a pipe completely full for a given pressure gradient. The relative permeability term is used to account for this effect.

LNAPL saturation varies with elevation across the gauged LNAPL thickness, where LNAPL conductivity is lowest near the oil/water interface and highest near the air/LNAPL interface. To provide a single metric for LNAPL mobility, the conductivity must be summed across the mobile LNAPL interval to give the LNAPL transmissivity.

Figure 3. Aquifer transmissivity versus hydraulic conductivity.

LNAPL transmissivity has been identified as a key metric for evaluating the likely effectiveness of direct LNAPL recovery compared to traditional measurements such as gauged LNAPL thickness in monitoring wells[11][12][6][13][14][15][16][17]). LNAPL transmissivity represents the volume of LNAPL flow a formation can produce per unit time over a unit width for a unit hydraulic gradient. Aquifer transmissivity is the primary metric for evaluating how much water can be produced from a water bearing unit in the subsurface and accounts for the thickness of the saturated aquifer and the ease with which the aquifer can transmit a given fluid per unit volume. The concept of transmissivity is illustrated in Figure 3. It is reasonable to apply similar thinking to estimation of the amount of LNAPL that could be produced by a particular subsurface matrix, and therefore transmissivity has become a key metric used to predict whether direct recovery (direct pumping) of LNAPL is likely to be effective.

The average LNAPL recovery rate was shown to be closely related to the average LNAPL transmissivity as well as to the LNAPL thickness in a series of 10-hour pump tests of three wells at an LNAPL-impacted site (Table 1, ITRC 2018)[1]. The measured LNAPL thickness in the source well (MW-1) was 3.7 times higher than in the LNAPL fringe well (MW-3), while the ratio of their average LNAPL transmissivities was 5. The average recovery rate was 12 times greater at the source well than at the fringe well. In this study, LNAPL thickness, average transmissivity and average recovery rate were all strongly correlated, with correlation coefficients of 0.94 and above.


References

  1. ^ 1.0 1.1 1.2 ITRC, 2018. LNAPL Site Management: LCSM evolution, decision process, and remedial technologies (LNAPL-3). Interstate Technical and Regulatory Council
  2. ^ Charbeneau, R.J., 2007. LNAPL Distribution and Recovery Model. Distribution and Recovery of Petroleum Hydrocarbon Liquids in Porous Media. Vol. 1. API Publication 4760. Report.pdf
  3. ^ 3.0 3.1 CRC CARE, 2018. Technical measurement guidance for LNAPL natural source zone depletion. Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Newcastle, Australia. Technical Report no. 44. 254p Report.pdf
  4. ^ Mahler, N., Sale, T. and Lyverse, M., 2012. A mass balance approach to resolving LNAPL stability. Groundwater, 50(6), pp.861-871. [10.1111/j.1745-6584.2012.00949.x 10.1111/j.1745-6584.2012.00949.x
  5. ^ Hawkins, A. M., 2013. Processes Controlling the behavior of LNAPLs at groundwater surface water interfaces, Master of Science Thesis, Colorado State University, Ft. Collins, Colorado. Report.pdf
  6. ^ 6.0 6.1 Huntley, D., 2000. Analytic determination of hydrocarbon transmissivity from baildown tests. Groundwater, 38(1), pp.46-52. doi: 10.1111/j.1745-6584.2000.tb00201.x
  7. ^ Mercer, J.W. and Cohen, R.M., 1990. A review of immiscible fluids in the subsurface: properties, models, characterization and remediation. Journal of contaminant hydrology, 6(2), pp.107-163. [Mercer, J.W. and Cohen, R.M., 1990. A review of immiscible fluids in the subsurface: properties, models, characterization and remediation. Journal of contaminant hydrology, 6(2), pp.107-163. doi: 10.1016/0169-7722(90)90043-G
  8. ^ 8.0 8.1 USEPA, 1996. How to effectively recover free product at leaking underground storage sites. A guide for state regulators. USEPA 510-R-96-001. U.S. Environmental Protection Agency, 162 pp. Report.pdf
  9. ^ Newell, C. J., S. D. Acree*, Ross, R.R., and Huling, S.G. 1995. Light non-aqueous phase liquid. U.S. Environmental Protection Agency, Washington, DC. EPA/540/S-95/500 (NTIS 95-267738) Report.pdf
  10. ^ Williams, D.E. and Wilder, D.G., 1971. Gasoline Pollution of a Ground‐Water Reservoir—A Case History a. Groundwater, 9(6), pp.50-56. doi: 10.1111/j.1745-6584.1971.tb03577.x
  11. ^ Kolhatkar, R., Kremesec, V., Rubin, S., Yukawa, C. and Senn, R., 1999. Application of field and analytical techniques to evaluate recoverability of subsurface free phase hydrocarbons. Petroleum Hydrocarbons and Organic Chemicals in Ground Water, pp.5-15.
  12. ^ Lundy, D.A. and Zimmerman, L.M., 1996, May. Assessing the recoverability of LNAPL plumes for recovery system conceptual design. In Proceedings of the 10th National Outdoor Action Conference and Expo (pp. 13-15).
  13. ^ Kirkman, A.J., 2013. Refinement of Bouwer‐Rice baildown test analysis. Groundwater Monitoring & Remediation, 33(1), pp.105-110. doi: 10.1111/j.1745-6592.2012.01411.x
  14. ^ ASTM, 2013. ASTM E2856-13, Standard guide for estimation of LNAPL transmissivity, ASTM International, West Conshohocken, PA.]
  15. ^ Charbeneau, R., A. Kirkman, and R. Muthu, 2016. API LNAPL Transmissivity Workbook: A Tool for Baildown Test Analysis – User Guide. American Petroleum Institute Publication 4762.
  16. ^ Palmier, C., Dodt, M. and Atteia, O., 2016. Comparison of Oil Transmissivity Methods Using Bail‐Down Test Data. Groundwater Monitoring & Remediation, 36(3), pp.73-83. Report.pdf
  17. ^ Lenhard, R.J., Rayner, J.L. and Davis, G.B., 2017. A practical tool for estimating subsurface LNAPL distributions and transmissivity using current and historical fluid levels in groundwater wells: Effects of entrapped and residual LNAPL. Journal of contaminant hydrology, 205, pp.1-11. Report.pdf

See Also